Online educational resource on achieving indoor environmental quality with radiant based HVAC systems
Not for profit educational resource on indoor environmental quality.
 Bookmark and Share
Fundamentals of indoor environmental quality / thermal comfort and air quality solutions using radiant based HVAC

Heating, Cooling and Ventilation Load Calculation Assessment (typically 40 page report for 14 zone system)
Bookmark and Share


Project Cover Page
Bookmark and Share


Drawing 1. Solar loading and system zoning analysis.
Bookmark and Share

Drawing 2. Mechanical room and distribution piping schematic.
Bookmark and Share

Drawing 3. Basement distribution piping and manifold locations.
Bookmark and Share

Drawing 4. Main floor distribution piping and manifold locations.
Bookmark and Share

Drawing 5. Basement floor radiant heating tube layout.
Bookmark and Share

Drawing 6. Main floor radiant heating tube layout.
Bookmark and Share

Drawing 7. Typical architectural/mechanical interfaces for radiant floors and ceilings
Bookmark and Share

Drawing 8.   Typical architectural/mechanical interfaces for radiant walls
Bookmark and Share

Drawing 9. Radiant floors and walls design details.
Bookmark and Share

Drawing 10. Typical radiant heating and cooling pipe installation specifications
Bookmark and Share

Drawing 11. Kitchen exhaust & make up air, space ventilation, filtration, humidification systems
Bookmark and Share

Drawing 12. Basement mechanical rooms and ventilation ducting layout.
Bookmark and Share

Drawing 13. Main floor ventilation ducting layout; kitchen range exhaust venting; and garage exhaust/make up system.
Bookmark and Share

Drawing 14. Equipment list, make, model, size and power requirements.
Bookmark and Share

Drawing 15. Main floor mini-split piping layout and equipment specifications.
Bookmark and Share


Project Photo's (under construction)

Figure 1. Southwest exposure

Figure 2 Southeast exposure

Figure 3 Gas fireplace in great room

Figure 4 Underfloor radiant heating manifolds

Figure 5 PV System (by others)

Figure 6 Ventilation system (HRV) with preheat coil for when unit goes into 100% make up air mode for kitchen exhaust system

More to come...


Professional Service Rates:

Indoor Climate Consulting Inc. rates are in-line with professional engineering and technologist fees based on a E3/C to E5/E and T3 to T7 classification as identified by The Consulting Engineers of Alberta in the document tilted, “Consulting Engineers Rate Guideline”.

Should you wish to discuss your project with us please contact us first via email and let us know about your project and expectations.


Robert Bean, R.E.T., P.L.(Eng.)
President, Indoor Climate Consultants Inc.
Registered Engineering Technologist - Building construction (ASET #8167)
Professional Licensee – Mechanical engineering (APEGA #105894)

Disclaimer/Terms of Use:

Indoor Climate Consultants Inc. has prepared these illustrations and specifications for internal use. The information contained within reflects best judgment in light of the information available at the time of preparation. Any use which a second or third party makes of these documents, or any reliance on or decisions to be made based on the documents, are the responsibility of such parties. Indoor Climate Consultants Inc. accepts no responsibility for damages, if any suffered by individuals or firms as a result of decisions made or actions taken based on these documents. These illustrations exclusively owned by the original author, are strictly limited for the purpose of illustrating the general layout, assembly and installation of equipment for Radiant Based HVAC Systems for residential structures and commercial building classifications A through E and F3, non hazardous, non explosion proof, restricted to four stories or less. These documents shall not be copied, reproduced, or altered by any means or method, nor shall it be distributed to any individual or companies without prior written authorization from the original author. All drawings and specifications are to be considered conceptual unless approved for construction by Robert Bean, R.E.T., P.L. (Eng.) for the specified client. Unless advised otherwise, any professional stamp placed on these documents relates to the general layout and assembly only.

For additional support visit our visitor services page.

Home | Seminars | Solutions | Heating Cafe | Contribute | Online Help | Bean's Blog | About Us | Glossary
Privacy Policy | Legal | Contact Us | Site Map |
Carlson-Holohan Award| Send Us Your Comments

Copyright © 2015 Healthy Heating. All rights reserved.1 2 3
Site developed by
Donate using PayPal, Credit Cards Accepted